Equipment Manufacturing Corporation

Santa Fe Springs, CA                                        (888) 833-9000                        sales@equipmentmanufacturing.com

Water Eater®

Electric Heated Water Evaporators

Equipment Manufacturing Corporation (EMC®) manufactures two electrically heated wastewater evaporators. Electric waste evaporators are simple to install and operate needing only an electrical connection and water vapor exhaust stack. 

The Model 85E evaporates approximately five gallons of water per hour and has an 85 gallon holding tank. It is through floor heated and uses strip heating elements attached to the underside of the floor. This makes the 85E easy to clean out and able to evaporate almost all of the water in the fluid. The 85E is normally recommended if you have less than 50 gallons per day of water to dispose of.

The Model 125E evaporates approximately twelve gallons of water per hour and has a 125 gallon holding tank. It uses immersion elements that directly heat the fluid. The Model 125E is useful for applications that need a higher evaporation rate and do not have access to natural gas or propane.


Electric Heated
Evaporators

WATER EATER®

Model 85E

Model 125E


EVAPORATION RATE*
5 Gallons/Hour (19 Liters/Hour)
12 Gallons/Hour (45 Liters/Hour)
TANK CAPACITY
85 Gallons (321 Liters)
125 Gallons (473 Liters)
TANK CONSTRUCTION**
12 Gauge Tank (316L Stainless Steel or Carbon Steel) 
1" Insulation, 16 Gauge Skin (Painted Carbon Steel)
HEAT SOURCE
Electric - 11.4 Kilowatt/Hour
Electric - 27 Kilowatt/Hour
HEAT EXCHANGER
Through Floor Heaters
Immersion Heaters
VENT STACK
6” Diameter
10" Diameter
TANK FLOOR
3/8" Plate Flat Bottom
Sloped with "U" Bottom
FLOOR SPACE (w/Pump or AFS)
23" x 41"  (33" x 41")
35" x 38"  (45" x 38")
OVERALL HEIGHT
44"
54"
TANK HEIGHT
30"
36"
CLEANOUT ACCESS
19" x 22½"
17" x 29"
ELECTRICAL
(Volts/Phase/Amps)

240/3/40 (Field Convertible to 1 Phase)
(480V Option)

240/3/68
(480/3/34 Option)

APPROXIMATE SHIP WEIGHT
450 lbs  (205 kg)
500 lbs  (230 kg)
* - Evaporation rate is affected by ambient temperature and humidity, altitude, solids on heat exchanger, floating materials, chemicals/ minerals which may raise the solution boiling point, exhaust restrictions, building pressure differential, low voltage, gas pressure, etc.  ** - Materials of Construction: The standard tank is carbon steel. The 316L Stainless Steel option includes the floor, inner side walls, top tank frame, rear decking, exhaust stack, drain & fill couplings, and the burner tube on gas heated machines. All material sizes (gauges & diameters) remain the same.
Water Eater® Info

Water Eater® 85E

Wastewater Evaporator Model 85E Water Eater

  • 5 GPH
  • Electric Heat
  • 85 Gallon Capacity

Water Eater® 125E

Wastewater Evaporator Model 125E Water Eater

  • 12 GPH
  • Electric Heat
  • 125 Gallon Capacity

Water Eater® 120G

Wastewater Evaporator Model 120G Water Eater

  • 15 GPH
  • Natural Gas/Propane Heat
  • 120 Gallon Capacity

Water Eater® 240GWastewater Evaporator Model 240G Water Eater

  • 22 GPH
  • Natural Gas/Propane Heat
  • 240 Gallon Capacity

Water Eater® 375G

Wastewater Evaporator Model 375G Water Eater

  • 40 GPH
  • Natural Gas/Propane Heat
  • 375 Gallon Capacity